Aeg-Electrolux 34942G-M User Manual

34942GGas hobOperating InstructionsGB

10Service and Spare PartsWhen you contact the Service Centre, they will need the followinginformation:1. Your name, address and post code.2. Your te

11Guarantee ConditionsStandard guarantee conditionsWe, AEG-Electrolux, undertake that if within 12 months of the date of the purchase this AEG-Electro

12OVERALL DIMENSIONS Width: 860 mmDepth: 500 mmHeight: 88 mmWeight: 16 KgCUT OUT DIMENSIONS Width: 830 mmDepth: 470 mmThickness: 30 mmSUPPLY CONNECTI

13Burner Dia. Tap By-pass1/100 mmAuxiliary 28Semi-rapid 32Rapid 40Triple-Crown 56Aeration adjustment noneBURNER RAPID SEMI-RAPID AUXILIARY TRIPLE(larg

14Important safety requirementsThis hob must be installed in accordance with the Gas Safety(Installation and Use) Regulations (Current Edition) and th

15CLEARANCES REQUIRED WHEN FITTING THE GAS HOBWITHOUT A COOKER HOOD ABOVECLEARANCES REQUIREDWHEN FITTING THE GAS HOBWITH A COOKER HOOD ABOVEInstallati

16A) End of shaft with nutB) WasherC) ElbowFO 0814FO 0264On the end of the shaft, which includes the G 1/2" threaded elbow,adjustment is fixed so

17Cut Out SizeThe dimensions of the cut-out are given in the diagram.Building InBuilding over a cupboard or drawerIf the hob is to be installed above

18ON/OFF SWITCHFLEXOUTLETON/OFF SWITCHFLEXOUTLETFO 0763FO 076412Building over a kitchen unit with doorProper arrangements must betaken in designing th

19Building inFitting the hob to the worktopBefore fitting the hob into thecut out, a sealing gasketsupplied with the hob must befitted to the edge of

2Important Safety InformationYou MUST read these warnings carefully before installing or using thehob. If you need assistance, contact our Customer Ca

20Electrical connectionsAny electrical work required to install this hob should be carried outby a qualified electrician or competent person, in accor

21Permanent ConnectionIn the case of a permanent connection, it is necessary that you installa double pole switch between the hob and the electricity

22Fault FindingPreliminary Electrical Systems CheckSTARTIsolate applianceand carry out:A: Earth Continuitycheck. Has inlet fuse blown?Carry out:C: Pol

23A. EARTH CONTINUITY CHECKAppliance must be electrically disconnected - meter set on ý (Ohms) x1 scale and adjust zero if necessary.— Test leads from

24Check gas supply atburnerIgnition System / Gas IgnitionYESCheck plug top fuse andreplace if necessaryCheck polarity and earthcontinuity of supply po

25CommissioningWhen the hob has been fully installed it will be necessary to check theminimum flame setting. To do this, follow the procedure below.1)

26Conversion from Natural Gas to LPGIt is important to note that this model is designed for use with naturalgas but can be converted for use with buta

27

35690-3001 03/05Grafiche MDM - Forlì From the Electrolux Group. The world’s No.1 choice.The Electrolux Group is the world’s

3 When using the hob for a long period of time, the ventilation shouldbe improved, by opening a window or increasing the extractor speed. Do not use

4ContentsImportant Safety Information ... 2Instructions for the User ...

5This appliance is manufactured according tothe following EEC directives:73/23 EEC - 90/683 EEC - 93/68 EEC -89/336 EEC - 90/396 EEC,current edition.G

61. Hob Top2. Rapid Burner3. Semi-rapid Burners4. Triple-crown Burner5. Auxiliary Burner6. Control knob for back left burner (semi-rapid)7. Control kn

7OperationBurner minimum maximumdiameter diameterTriple-crown (ultra-rapid) 160 mm 260 mmLarge (rapid) 160 mm 240 mmMedium (semi-rapid) 120 mm 220 mmS

8Before any maintenance or cleaning can be carried out, you mustDISCONNECT the hob from the electricity supply.The hob is best cleaned whilst it is st

9Something Not Working?If the hob is not working correctly, please carry out the following checksbefore contacting your local Service Force Centre.