Aeg-Electrolux PE8038-M/UK User Manual

1CONTENTS 1. Describing the espresso machine 2. Description of the control panel: touch keys 3. Safety instructions 4. Instructions for the

10 PRELIMINARY STARTING: FIRST USE − After filling up the water reservoir, open the steam/water cock as it is shown in the figure. − Switch t

11 − After the water has flowed out (if necessary, repeat the draining operation several times), close the knob again. − As soon as the heating

12 − A faint flashing of all the LEDs will signal that the factory values have been reset. N.B.: The standard values only concern the quantity of w

13 − Extract the espresso machine out of the cabinet sliding on the special slides. − Turning the proper adjusting knob (A-10) will modif

14STAND-BY MODE − Once powered and inserted into the cabinet, the machine is in stand-by mode: this will be signaled by the on/off LED blinking.

156. DRAWER (OPTIONAL) − This machine can also be provided with an optional well-equipped drawer mod. PES 8036-m, with front panel of stainless st

16 − Insert the filter holder under the coffee measuring device by pressing the proper button slightly: thus the right quantity of ground coffee w

17 − Lock the filter holder perfectly turning its handle from left to right. − When preparing an espresso, use the proper grille in

18 − Press the coffee button and the quantity of coffee in the cup will be that selected and recorded before. Remove the filter holder from the nut

19 − This machine is also prearranged to operate with paper pods, that is throwaway portions of roasted coffee (for only one cup of coffee). − Carr

21. DESCRIPTION OF THE ESPRESSO MACHINE 1. Locking nut of filter holder 2. Steam/water pipe 3. Coffee pressing tool 4. Grinder button 5. C

208. HOT WATER − The steam/water pipe is of foldaway type: extract by rotating as it is shown in the figure.. − Place a container u

21 − Close the steam/water knob again. 9. STEAM HEATING LIQUIDS − Press the steam button once. Both the LEDs of steam and water temperature

22 − Place a pot with the liquid to be heated under the steam nozzle and turn the steam knob in anticlockwise direction. − Wait until the liq

2310. PROGRAMMING THE QUANTITY OF GROUND COFFEE − This espresso machine has already been calibrated in factory to dispense the ideal measure of gro

2411. PROGRAMMING THE QUANTITY OF COFFEE POURED IN THE CUP − The quantity of coffee being poured can be adjusted as desired. Turn the coffee mea

25 − Once obtained the desired quantity of coffee press the button again and this coffee measure will be stored automatically. 12. PROGRAMMIN

26 − Release the button when the water starts flowing out; then, once obtained the desired quantity of water press the button again and this measur

27COLD ESPRESSO SHAKE Frothy and extremely refreshing, this drink is delicious on hot days. Prepare an espresso, add sugar and pour into a shaker wi

28DRIP TRAY − Remove the drip tray from the machine as it is shown in the figures above. − Make sure that the drip tray is periodically drained to

29− The steam nozzle should be periodically cleaned. Preparing milk for cappuccinos could dirty the inside of this nozzle. Therefore remove it as it

32. DESCRIPTION OF THE CONTROL PANEL: TOUCH KEYS 1. Water temperature indicator 2. ON/stand-by indicator 3. Coffee indicator 4. Water indica

30 COMPONENTS FOR INSTALLING THE MACHINE This espresso machine will be installed into cabinets with height of 380 mm and width ranging from 560 mm t

31 − Unscrew the cable clap available on the machine. − Fix the power cord onto the machine as it is shown in the figure. −

32INSTALLING THE MACHINE WITHOUT DRAWER − Lay the fixing base of the machine equipment on the shelf of the cabinet. − Insert t

33 − Fix the base plate inserting 4 self-threading screws into the 4 fore holes of the same plate. Then assemble the 2 slides with the remaining

34INSTALLING THE ALIGNING BAR − When this espresso machine is assembled in a composition of electric household appliances, it could be installed b

35INSTALLING MACHINE + DRAWER − Lay the fixing base of the drawer onto the proper shelf of the cabinet. − Insert the side plates o

36 − Fix the base plate inserting 4 self-threading screws into the 4 fore holes of the plate. Then assemble the 2 slides with the remaining 10 sel

37 − Four side plates (two being 2 mm thick and two 1 mm thick) are provided together with the machine, to compensate for the different possible

38 − Insert the machine coupling its slides with those already mounted onto the cabinet’s sides and slide it into the cabinet to the stops until

39 17. TECHNICAL SPECIFICATIONS As regards the general dimensions of the machine, please see the fig. D − Width 594 mm − Dep

43. SAFETY INSTRUCTIONS Using this machine is very easy. However, please read this instruction manual carefully and thoroughly before installing a

40 FUSES F1: Fuse Ø 5 x 20 mm - Vn = 250 V - In=10 A F2: Fuse Ø 5 x 20 mm – Vn = 250 V – In = 0.5 A

4118. DECLARATION OF GUARANTEE TERMS SERVICE & SPARE PARTS If you wish to purchase spare parts or require an engineer, contact your local AEG

42GUARANTEE CONDITIONS AEG offer the following guarantee to the first purchaser of this appliance. 1. The guarantee is valid for 12 months commencin

5FOR INSTALLATION AND SERVICING − This machine must be installed and connected to the mains by a SKILLFUL ENGINEER. Make sure that the machine is D

64. INSTRUCTIONS FOR THE FIRST USE OF THE MACHINE FILLING UP THE WATER RESERVOIR − Press the unlocking levers available under the drip tray a

7 Hardness of water: − Before filling up the water reservoir, make sure that the decalcifying Brita filter has been soaked in cold water for at least

8 − Insert the machine into the cabinet pushing slightly until “CLIK!” can be heard: this is the signal that the machine has been locked.

9 − Pour approximately 200 g of coffee beans into the container availabe on the right side of the machine − Insert the machine into