Aeg-Electrolux L61470FL User Manual

L 61470 FL EN User manual

6. PROGRAMMESProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsKoch/Bunt95° - ColdWhite and colouredcotton with normalsoil.m

ProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsPumpen All fabricsThe maximum loadof the laundry is rela-ted to the type o

The washing temperature of the washing phase may differ from the temperature de-clared for the selected programme.7. CONSUMPTION VALUESAt programme st

8. BEFORE FIRST USE1.To activate the drain system, put 2 li-tre of water in the main wash com-partment of the detergent dispens-er.2.Put a small quant

The detergent compartment for the prewash phase, the soakprogramme and for the stain function.Add the detergent for prewash, soak and stain remover be

4.To use liquid detergent, turn theflap down.With the flap in the positionDOWN:– Do not use gelatinous or thickliquid detergents.– Do not put more liq

2.Press button 4 , the appliancestarts the countdown of the delaystart.When the countdown is completed,the programme starts automatically.Before you p

10. HINTS AND TIPS10.1 The laundry load• Divide the laundry in: white, coloured,synthetics, delicates and wool.• Obey the washing instructions that ar

Water hardness tableLevel TypeWater hardness°dH °T.H. mmol/l Clarke1 soft 0-7 0-15 0-1.5 0-92 medium 8-14 16-25 1.6-2.5 10-163 hard 15-21 26-37 2.6-3.

11.6 Detergent dispenserTo clean the dispenser:121.Press the lever.2.Pull the dispenser out.3.Remove the top part of the liquidadditive compartment.4.

CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. SAFETY

To clean the drain pump:1.Open the drain pump door.2.Put a container below the recess ofthe drain pump to collect the waterthat flows out.3.Press the

218.Clean the filter under the water tapand put it back in the pump into thespecial guides.9.Make sure that you tighten correctlythe filter to prevent

45°20°6.Install again the inlet hose. Makesure that the couplings are tight toprevent leakages.7.Open the water tap.11.9 Emergency drainBecause of a m

Problem Possible cause Possible solution The filters in the waterinlet hose is blocked .Clean the filters. Refer to 'Careand cleaning'. Th

Problem Possible cause Possible solution You did not press but-ton 4 .Press button 4 . The delay start is set. To start immediately the pro-gramme,

13. INSTALLATION13.1 Fixing plate kit(4055171146)Available from your authorized dealer.If you install the appliance on a plinth,secure the appliance i

5.Open the door and remove all theitems from the drum.6.Put one of the polystyrene packag-ing elements on the floor behindthe appliance. Carefully put

10.Remove the three bolts. Use the keysupplied with the appliance.11.Pull out the plastic spacers.12.Put the plastic caps in the holes.You can find th

13.3 Positioning and levellingx4• Install the appliance on a flat hardfloor.• Make sure that carpets do not stopthe air circulation below the applianc

• Connect the water inlet hose to thecold water tap with 3/4 thread.CAUTION!Make sure that there are no leaksfrom the couplings.Do not use an extensio

1. SAFETY INFORMATIONBefore the installation and use of the appliance, careful-ly read the supplied instructions. The manufacturer isnot responsible i

• On the edge of a sink.• Make sure that the plastic guide can-not move when the appliance drains.Attach the guide to the water tap orthe wall.• To a

14. ENVIRONMENT CONCERNSRecycle the materials with thesymbol . Put the packaging inapplicable containers to recycle it.Help protect the environment a

www.aeg.com/shop132930511-B-462012

• If the supply cord is damaged, it must be replaced bythe manufacturer, its service agent or similarly quali-fied persons in order to avoid a hazard.

Water connection• Make sure not to cause damage to thewater hoses.• The appliance is to be connected tothe water mains using the new sup-plied hose-se

Water supply pressure Minimum 0,5 bar (0,05 MPa)Maximum 8 bar (0,8 MPa)Water supply 1) Cold waterMaximum load Cotton 7 kgSpin speed Maximum 1400 rpm1

4.1 Accessories1 2341SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit

• After 5 minutes from the end of thewashing programme. Refer to 'At theend of programme'.5.2 Programme knob 2Turn this knob to set a progra

5.4 Start/Pause button 4Press button 4 to start or interrupt aprogramme.5.5 Delay start button 5Press button 5 to delay the start of aprogramme from 3