L 75475 FLL 75675 FLEN User manual
Spin phase is off.'Rinse Hold' function ison.5.10 Temperature button 10Press button 10 to change the defaulttemperature.- - = cold water5.11
ProgrammeTemperatureType of loadmax. weight ofloadCycledescriptionFunctionsExtra Leise95° - ColdWhite and colouredcotton with normalsoil.max. 7 kgStop
ProgrammeTemperatureType of loadmax. weight ofloadCycledescriptionFunctionsGardinen40° - ColdSet this programmeto wash curtains. Itadds automaticallyt
7) Standard programmes for the Energy Label consumption values. According toregulation 1061/2010, these programmes are respectively the “standard 60°
Programmes Load(Kg)Energy con-sumption(kWh)Water con-sumption (li-tre)Approxi-mate pro-grammeduration(minutes)Remainingmoisture(%)1)The information gi
8.2 Using the detergent andadditivesThe detergent compartment for the prewash phase and thesoak programme.Add the detergent for prewash and soak befor
3.To use powder detergent, turn theflap up.4.To use liquid detergent, turn theflap down.With the flap in the positionDOWN:– Do not use gelatinous or t
2.Press button 1 again to activatethe appliance. Now, you can set anew washing programme.The appliance does not drain thewater.8.6 Change a functionYo
2.Press the Start/Pause button 4 .The appliance drain the water andspin.3.When the programme is completedand the door lock symbol goes off,you can ope
• mmol/l (millimol for each litre - inter-national unit for the hardness of wa-ter).• Clarke degrees.Water hardness tableLevel TypeWater hardness°dH °
CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. SAFETY
10.5 DrumRegularly examine the drum to preventlimescale and rust particles.Only use special products to remove rustparticles from the drum.To do this:
To clean the drain pump:1.Open the drain pump door.2.Pull the flap out to remove it.3.Put a container below the recess ofthe drain pump to collect the
129.Clean the filter under the water tapand put it back in the pump into thespecial guides.10.Make sure that you tighten correctlythe filter to preven
Put the drainage duct back and close thedrain pump flap.When you drain the water with the emer-gency drain procedure, you must acti-vate again the dra
Problem Possible cause Possible solutionThe appliancedoes not drain thewater.The water drain hose isdamaged.Make sure that the water drainhose has no
Problem Possible cause Possible solution Leakages from the drainpump.Make sure that the drain pumpfilter is tight. The water drain hose isdamaged.Ma
12.2 Unpacking1.Use the gloves. Remove the externalfilm. If necessary, use a cutter.2.Remove the cardboard top.3.Remove the polystyrene packagingmater
6.Put one of the polystyrene packag-ing elements on the floor behindthe appliance. Carefully put downthe appliance with the rear side onit. Make sure
12.Put the plastic caps in the holes.You can find these caps in the usermanual bag.WARNING!Remove all the packaging andthe transit bolts before you in
12.4 The inlet hose20O20O20O45O45O45O• Connect the hose to the appliance.Turn the inlet hose only left or right.Loose the ring nut to set it in the co
1. SAFETY INFORMATIONBefore the installation and use of the appliance, careful-ly read the supplied instructions. The manufacturer isnot responsible i
With the plastic hose guide. • On the edge of a sink.• Make sure that the plastic guide can-not move when the appliance drains.Attach the guide to the
You can extend the drain hose tomaximum 400 cm. Contact theservice centre for the other drainhose and the extension.13. ENVIRONMENT CONCERNSRecycle th
www.aeg.com/shop132940922-A-412012
• If the supply cord is damaged, it must be replaced bythe manufacturer, its service agent or similarly quali-fied persons in order to avoid a hazard.
Water connection• Make sure not to cause damage to thewater hoses.• The appliance is to be connected tothe water mains using the new sup-plied hose-se
Water supply pressure Minimum 0,5 bar (0,05 MPa)Maximum 8 bar (0,8 MPa)Water supply 1) Cold waterMaximum load Cotton 7 kgSpin speed Maximum 1400 rpm
1 2341SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit bolts.3Anti-fl
5.3 Display 3A B C DThe display shows:A • The maximum temperature of the programme.B • The default spin speed of the programme.•'No Spin'1)
D • The programme timeWhen the programme starts, the time decreases with steps of 1 mi-nute.• The delay startWhen you press the delay start button, th
Comments to this Manuals