L 75475 FLL 75675 FLWASHING MACHINE USER MANUAL
Spin phase is off.'Rinse Hold' function ison.TEMPERATURE BUTTON 10Press button 10 to change the defaulttemperature.- - = cold waterACOUSTIC
ProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsExtra Leise95° - ColdWhite and colouredcotton with normalsoil.max. 7 kgSto
ProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsGardinen40° - ColdSet this programmeto wash curtains. Itadds automatically
CONSUMPTION VALUESProgramme1)Energy consumption(KWh)2)Water consump-tion (litre)2)White Cottons 95 °C 2.4 73Cottons 60 °C 1.5 69Cottons 40 °C 0.90 69S
2. Put the laundry in the drum, oneitem at a time. Shake the items be-fore you put them in the appliance.Make sure not to put too muchlaundry in the d
Always obey the instructions that you find on the packaging of the deter-gent products.Check the position of the flap1. Pull out the detergent dispens
SETTING AND STARTING A PROGRAMME1. Turn the programme knob. The re-lated programme indicator comeson.2.The indicator of button 4 flasheswith red colou
If you deactivate the appliance,it is necessary to set the pro-gramme again.AT THE END OF PROGRAMME• The appliance stops automatically.• The acoustic
STUBBORN STAINSFor some stains, water and detergent isnot sufficient.We recommend that you remove thesestains before you put the items in theappliance
EXTERNAL CLEANINGClean the appliance only with soap andwarm water. Fully dry all the surfaces.CAUTION!Do not use alcohol, solvents orchemical products
SERVICEWhen contacting Service, ensure thatyou have the following data available.The information can be found on therating plate.ModelPNCSerial Numbe
3. Remove the top part of the liquidadditive compartment.4. Clean all the parts with water.5. Clean the dispenser recess with abrush.6. Put back the d
3. Put a container below the recess ofthe drain pump to collect the waterthat flows out.4. Press the two levers and pull for-ward the drainage duct to
To clean the water inlet filters:1. Close the water tap.2. Remove the water inlet hose fromthe water tap.3. Clean the filter in the inlet hose witha s
TROUBLE SHOOTER AND SERVICEThe start of the appliance does not oc-cur or it stops during operation.First try to find a solution to the prob-lem (refer
Problem Possible cause Possible solutionThe anti-flood de-vice is on. • Disconnect the appliance.• Close the water tap.• Contact the service centre.T
Problem Possible cause Possible solutionThe appliance fillswith water anddrain immediately.The end of the drainhose is too low.Make sure that the drai
Maximum load Cotton 7 kgSpin speed Maximum 1400 rpm (L 75478 FL)1600 rpm (L 75678 FL)1) Connect the water inlet hose to a water tap with a 3/4'&a
5. Open the door. Remove the poly-styrene piece from the door sealand all the items from the drum.6. Put the front piece on the floor be-hind the appl
10.Remove the three bolts. Use the keysupplied with the appliance.11.Pull out the plastic spacers.12.Replace the plastic spacers with theplastic caps.
• The appliance must be level and sta-ble.CAUTION!Do not put cardboard, wood orequivalent materials below theappliance feet to adjust the lev-el.THE I
FOR PERFECT RESULTSThank you for choosing this AEG product. We have created it to give youimpeccable performance for many years, with innovative techn
Water-stop deviceAThe inlet hose has a water stop device.This device prevents water leaks in thehose because of its natural ageing. Thered sector in t
Without the plastic hose guide.•To a sink spigot.Refer to the illustration. Put the drainhose in the spigot and tighten it witha clip. Make sure that
www.aeg.com/shop 132940921-A-492010
SAFETY INFORMATIONBefore the installation and use, readthis manual carefully:• For your safety and the safety of yourproperty• To help the environmen
internal components and cause leak-ages or malfunctions.• Do not install and connect a dam-aged appliance.• Make sure to remove all packagingand trans
• To use the correct quantity of the de-tergent, check the water hardness ofyour domestic systemThe symbol on the product or on itspackaging indicate
ACCESSORIES1 2341SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit bol
DISPLAY 3A B C DThe display shows:A • The maximum temperature of the programme.B • The default spin speed of the programme.•'No Spin'1) and
D • The programme timeWhen the programme starts, the time decreases with steps of 1 minute.• The delay startWhen you press the delay start button, the
Comments to this Manuals