L 75485 FLL 75685 FLWASHING MACHINE USER MANUAL
PERMANENT EXTRA RINSEFUNCTIONWith this function you can keep the ex-tra rinse function permanently on whenyou set a new programme.• To activate the fu
ProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsWolle/Seide 40° - ColdMachine washablewool. Hand washablewool and delicate
STEAM PROGRAMMESProgramme1)Type of load Max. loadAuffrischenThis cycle removes odours fromthe laundry.Steam does not removeanimal odours.Cotton and sy
2) The consumption information shown in this chart is indicative. It can vary depending on thequantity and the type of laundry, on the temperature of
USING THE DETERGENT AND ADDITIVESThe detergent compartment for the prewash phase and the soakprogramme.Add the detergent for prewash and soak before t
3. To use powder detergent, turn theflap up.4. To use liquid detergent, turn theflap down.With the flap in the positionDOWN:– Do not use gelatinous or
CHANGE A FUNCTIONYou can change only some functionsbefore they operate.1.Press button 4 . The indicatorflashes.2. Change the function set.SET THE DELA
The washing programme iscompleted, but there is water in thedrum:– The drum turns regularly to preventthe creases in the laundry.–The door stays locke
you use a water softener for washingmachines. In areas where the waterhardness is soft it is not necessary touse a water softener.To know the water ha
DOOR SEALRegularly examine the seal and removeall objects from the inner part.DRUMRegularly examine the drum to preventlimescale and rust particles.On
SERVICEWhen contacting Service, ensure thatyou have the following data available.The information can be found on therating plate.ModelPNCSerial Numbe
DRAIN PUMPRegularly examine the drainpump and make sure that it isclean.Clean the pump if:• The appliance does not drain the wa-ter.• The drum cannot
7. Remove fluff and objects from thepump.8. Make sure that the impeller of thepump can turn. If this does not oc-cur, contact the service centre.129.
4. Remove the inlet hose behind theappliance.5. Clean the filter in the valve with astiff brush or a towel.45°35°6. Install again the inlet hose. Make
Problem Possible cause Possible solutionThe appliancedoes not fill withwater.The water tap is closed. Open the water tap. The water inlet hose isdama
Problem Possible cause Possible solutionThe programmedoes not start.The mains plug is notconnected in the mainssocket.Put in the mains plug. Blow out
After the check, activate the appliance.The programme continues from thepoint of interruption.If the problem occurs again, contact theservice centre.I
INSTALLATIONUNPACKING1. Use the gloves. Remove the exter-nal film. If necessary, use a cutter.2. Remove the cardboard top.3. Remove the polystyrene pa
6. Put the front piece on the floor be-hind the appliance. Carefully putdown the appliance with the rearside on it. Make sure not to damagethe hoses.1
12.Replace the plastic spacers with theplastic caps. You can find these capsin the user manual bag.WARNING!Remove all the packaging andthe transit bol
THE INLET HOSE35O35O35O45O45O45O• Connect the hose to the appliance.Turn the inlet hose only left or right.Loose the ring nut to set it in the cor-rec
FOR PERFECT RESULTSThank you for choosing this AEG product. We have created it to give youimpeccable performance for many years, with innovative techn
With the plastic hose guide. • On the edge of a sink.• Make sure that the plastic guide can-not move when the appliance drains.Attach the guide to the
You can extend the drain hoseto maximum 400 mm. Contactthe service centre for the otherdrain hose and the extension.ENGLISH 31
www.aeg-electrolux.com/shop 132940811-A-482010
SAFETY INFORMATIONBefore the installation and use, readthis manual carefully:• For your safety and the safety of yourproperty• To help the environmen
internal components and cause leak-ages or malfunctions.• Do not install and connect a dam-aged appliance.• Make sure to remove all packagingand trans
• To use the correct quantity of the de-tergent, check the water hardness ofyour domestic systemThe symbol on the product or on itspackaging indicate
ACCESSORIES1 2341SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit bol
The display shows:A • The maximum temperature of the programme.B • The default spin speed of the programme.•'No Spin'1) and 'Rinse Hold
TIME SAVE BUTTON 6Press the button 6 to decrease theprogramme duration.• Press one time to set 'Shortened du-ration' for items with daily so
Comments to this Manuals