L 87480 FL EN User manual
- -, the appliance does not heat the wa-ter.4.11 Acoustic signals functionYou can hear the acoustic signals when:• You turn the appliance on.• You tur
ProgrammeTemperatureType of loadMax. weight of loadCycle de-scriptionFunctionsSynthetics60° - ColdSynthetic or mixed fab-ric items with normalsoil.max
ProgrammeTemperatureType of loadMax. weight of loadCycle de-scriptionFunctionsSpin / Drain 5)0°All fabrics.The maximum load ofthe laundry is related t
STEAM PROGRAMMESProgramme1)Type of load Max load Steam – RefreshThis cycle removes odours from thelaundry.Steam does not remove animalodours.Cotton an
7. USING THE APPLIANCE1.Open the water tap.2.Connect the mains plug to the mainssocket.3.Press button 1 to activate the ap-pliance.4.Put the laundry i
This is the maximum level for the quantity of liquid additives.The compartment for the stain remover.Put the product in the compartment and set the st
5.Measure out the detergent and thefabric conditioner.6.Carefully close the detergent dis-penser. Make sure that the flapdoes not cause a blockage whe
If the temperature and level ofthe water in the drum are toohigh, the door lock symbol stayson and you cannot open thedoor. To open the door do theste
• A very small load can cause balanceproblems with the spin phase. If thisoccurs, adjust the items in the tubmanually and start the spin phaseagain.8.
find on the packaging of the manufactur-er.Do this as an extra wash cycle withoutlaundry.9.2 External cleaningOnly clean the appliance with warmsoapy
CONTENTS1. SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. TECHNI
3.Remove the top part of the liquidadditive compartment.4.Clean all the parts with water.5.Clean the dispenser recess with abrush.6.Put the dispenser
3.Put a container below the recess ofthe drain pump to collect the waterthat flows out.4.Press the two levers and pull for-ward the drainage duct to l
To clean the water inlet filters:1.Close the water tap.2.Remove the water inlet hose fromthe water tap.3.Clean the filter in the inlet hose witha stif
10. TROUBLESHOOTINGThe appliance does not start or it stopsduring operation.First try to find a solution to the problem(refer to the table). If not, c
Problem Possible cause Possible solutionThe anti-flood de-vice is on. • Disconnect the appliance.• Close the water tap.• Contact the service centre.T
Problem Possible cause Possible solutionThe appliance fillswith water anddrains immediate-ly.The end of the drainhose is too low.Make sure that the dr
4.Remove the internal film.5.Open the door. Remove the poly-styrene piece from the door sealand all the items from the drum.6.Put one of the polystyre
9.Remove the power supply cable andthe drain hose from the hose hold-ers.10.Remove the three transit bolts. Usethe key supplied with the appliance.11.
11.2 Positioning and levellingx4• Install the appliance on a flat hardfloor.• Make sure that carpets do not stopthe air circulation below the applianc
• Connect the water inlet hose to thecold water tap with ¾” thread.CAUTION!Make sure that there are no leaksfrom the couplings.Do not use an extension
1. SAFETY INSTRUCTIONS1.1 Conditions of useThis appliance is intended to be used inhousehold and similar applications suchas:• Farm houses.• By clien
• On the edge of a sink.• Make sure that the plastic guide can-not move when the appliance drains.Attach the guide to the water tap orthe wall.• To a
12. WARRANTYFOR SALES IN AUSTRALIA AND NEWZEALANDALL AEG BRANDED APPLIANCESThis document sets out the terms andconditions of the product warrantiesfor
ance is transported at the owner’scost and risk while in transit to andfrom AEG or its ASC.6.Proof of purchase is required beforeyou can make a claim
Before calling for service, please ensure that the steps listed in point 13 above havebeen followed.SERVICE AUSTRALIAwww.aeg.com/auFOR SERVICEor to fi
34www.aeg.com/au
ENGLISH 35
www.aeg.com/au132935721-A-382012
1.6 Installation• The appliance is heavy, be carefulwhen you move it.• Do not transport your appliance with-out the transit bolts, you can damageinter
Electrical connection: VoltageOverall powerFrequency230-240 V2200 W50 HzLevel of protection against ingress of solid particlesand moisture ensured by
3.1 Accessories1 2341SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit
• After 5 minutes from the end of thewashing programme. Refer to 'At theend of programme'.4.2 Programme knob 2Turn this knob to set a progra
EThe detergent overdosing comes on at the end of the cy-cle when the appliance detects too much detergent.FYou cannot open the door when this symbol i
The value shows the total number of the rinses.The indicator bar is fully filled when you set to the maxi-mum number of rinses.LThe Stain symbol comes
Comments to this Manuals