34602GGas hobOperating InstructionsGB
10Service and Spare PartsWhen you contact the Service Force Centre, they will need the following information:1. Your name, address and post code.2. Yo
11For general enquiries concerning your AEG-Electrolux appliance and for further informationon AEG-Electrolux products, contact our Customer Care Depa
12Guarantee ConditionsAEG-Electrolux offer the following guarantee to the first purchaser of this appliance.1. The guarantee is valid for 12 months co
13Overall dimensionsWidth: 580 mm.Depth: 500 mm.Cut out dimensionsWidth: 550 mm.Depth: 470 mm.Supply ConnectionsGas: RC 1/2 inch (1/2 inch male) Rear
14Important safety requirementsThis hob must be installed in accordance with the Gas Safety (Installation and Use)Regulations (Current Edition) and th
15650 mm400 mm400 mm100 mm50 mm50 mm55 mm600 mm700 mm400 mm100 mm400 mm50 mm55 mm50 mmCLEARANCES REQUIRED WHEN FITTING THE GAS HOBWITHOUT A COOKER HOO
16A) End of shaft with nutB) WasherC) ElbowFO 0814FO 0264On the end of the shaft, which includes the GJ 1/2" threaded elbow, adjustment is fixed
17FO 2291Cut Out SizeThe dimensions of the cut-out are given in the diagram.Building InBuilding over a cupboard or drawerIf the hob is to be installed
18ON/OFF SWITCHFLEXOUTLETON/OFF SWITCHFLEXOUTLETFO 0763FO 076412Building over a kitchen unitwith doorProper arrangements must be taken indesigning the
19Fitting the hob to the worktopBefore fitting the hob into the cut out, asealing gasket supplied with the hob mustbe fitted to the edge of the cut ou
20Electrical connectionsAny electrical work required to install this hob should be carried out by a qualifiedelectrician or competent person, in accor
21Permanent ConnectionIn the case of a permanent connection, it is necessary that you install a double poleswitch between the hob and the electricity
22Fault FindingPreliminary Electrical Systems CheckSTARTIsolate applianceand carry out:A: Earth Continuitycheck. Has inlet fuse blown?Carry out:C: Pol
23A. EARTH CONTINUITY CHECKAppliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale andadjust zero if necessary.— Test leads fro
24Check gas supply atburnerIgnition System / Gas IgnitionYESCheck plug top fuse andreplace if necessaryCheck polarity and earthcontinuity of supply po
25CommissioningWhen the hob has been fully installed it will be necessary to check the minimum flame setting. Todo this, follow the procedure below.1)
26Conversion from Natural Gas to LPGIt is important to note that this model is designed for use with natural gas but can beconverted for use with buta
35690-2901 03/05Grafiche MDM - Forlì From the Electrolux Group. The world’s No.1 choice.The
3 Important Safety InformationYou MUST read these warnings carefully before installing or using the hob. Ifyou need assistance, contact our Customer C
4z When using other electrical appliances, ensure the cable does not come into contactwith the hot surfaces of the cooking appliance.z Unstable or mis
5This appliance is manufactured according to the following EEC directives:73/23 EEC - 90/683 EEC - 93/68 EEC -89/336 EEC - 90/396 EEC,current edition.
61. Hob Top2. Rapid Burner3. Semi-rapid Burners4. Auxiliary Burner5. Control knob for back right burner (semi-rapid)6. Control knob for back left burn
7Hob burnersTo light a burner:z turn the relevant control knob anticlockwise to the maximum position, then push it down toignite the burner. Upon, ign
8Before any maintenance or cleaning can be carried out, you must DISCONNECT thehob from the electricity supply.The hob is best cleaned whilst it is st
9Something Not Working?If the hob is not working correctly, please carry out the following checks before contactingyour local Service Force Centre.
Comments to this Manuals