AEG Electrolux CaFamosa Operations Instructions download pdf (Page 11)

g

24

0 Now press the “1 Cup“ button for

one cup or the “2 Cups“ button

for two cups.

Note: If the “Ground Coffee“ but-

ton is pressed inadvertently, you can

cancel this setting by pressing the

“1 Cup“ button again. The appliance

then performs a normal flush.

4. Frothing Milk (for Cappuc-

cino) (Figure 15, 16)

Hot steam can be used both for froth-

ing milk for cappuccino and for heat-

ing liquids.

Note: For one cup of cappuccino, fill a

large cup up to 2/3 full with espresso

and then add the frothed milk.

Frothing milk:

Slide the moving tube on the swivel-

ling nozzle all the way down (Figure

15/A).

Warming liquids:

Slide the moving tube up (Figure 15/B).

0 Switch on the appliance using the On/

Off switch (Figure 2/B) and flush if

necessary (see Section 2.5.). The appli-

ance is ready for use when the “1

Normal Cup“ indicator (Figure 2/D)

illuminates.

0 Immerse the swivelling nozzle in the

container with the milk to be frothed

or the liquid to be heated, and start

the production of steam by turning the

selection dial (Figure 1/E) anticlock-

wise to the stop (Figure 16/A).

Due the nature of the system, a little

water runs out of the swivelling nozzle

first, this can be run off first, however

it will not affect the quality of the

result, e.g., on frothing milk.

Important: Only immerse the swivel-

ling nozzle around half way into the

liquid so that air can be drawn in

unhindered. The swivelling nozzle

should not touch the base of the con-

tainer to avoid the hindrance of the

outlet of steam. Important: There is a

risk of burns!

0 You can stop the outlet of steam by

turning the selector dial clockwise to

the O-position (Figure 16/B).

In particular after frothing milk, it is

recommended to briefly activate the

outlet of steam to “blow out the swiv-

elling nozzle“. Then clean the any milk

residues from the swivelling nozzle

using a damp cloth. Move the moving

metal tube up and down during this

process.

After steam has been drawn off, all

4 green indicators flash to indicate

that the system must be refilled with

water. Proceed as follows:

0 Place a container under the swivelling

nozzle (Figure 1/F).

0 Turn the selector dial (Figure 1/E) anti-

clockwise to the stop (Figure 16/A).

0 Press the “Flush“ button (Figure

2/K). Wait until the flow of water stops

automatically. All 4 green indicators

then flash.

0 Turn the selector dial (Figure 1/E)

clockwise back to the 0-position (Fig-

ure 16/B). The appliance is now ready

for use again.

5. Preparing Hot Water

(Figure 16)

You can use the hot water function for

prewarming cups, for preparing instant

beverages or tea. Important: There is a

risk of burns!

0 Switch on the appliance using the On/

Off switch (Figure 2/B) and flush if

necessary (see Section 2.5.). The appli-

ance is ready for use when the “1

Normal Cup“ indicator (Figure 2/D)

illuminates.

0 Hold a container under the swivelling

nozzle and initiate the preparation of

hot water by turning the selector dial

(Figure 1/E) anticlockwise to the stop

(Figure 16/A) and press the “Flush“

button (Figure 2/K).

0 You can stop the flow of hot water by

turning the selector dial clockwise

back to the O-position (Figure 16/B).

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 17 18

Comments to this Manuals

No comments